Conformal Coating

Verification items related to conformal coating, Selective spray conformal coating, and Dip conformal coating.

Selective Coating

  • Definition
    • Component
      • Coated Component: Set the Coating essential components and Measure Base.
        • Measure
      • Non-coated Component: Set the Coating Restricted Components and Measure Base.
        • Measure
      • Test Point(Pad)
        • Component Group: Set the Test Point designed as a Component.
        • Pad/Via Padstack String: Set the Test Point designed with route Pads or Vias.
    • Slit and Cut-out
      • Layer: Selecting the Artwork Layer Defined for Slit or Board Cut-out Areas.
        • ** If there is a closed PCB outline within the PCB board area, it is recognized as a cut-out area.
      • Minimum Width: Set the Minimum Width for Recognizing Slits and Holes.
    • Coated Area
      • Layer: Set the Artwork Layer with the Coating Required Area.
        • Top
        • Bottom
      • Component Group: Set the Components and Measure Base for recognizing the Coated Area.
        • Measure
      • Expand Area: Set the value for the expanding area from the component.
    • Non-coated Area
      • Layer: Set the Artwork Layer with the Non-coating Required Area.
        • Top
        • Bottom
    • Target Layer
      • All: Verify Both Top and Bottom Layer.
      • Top: Verify Top Layer.
      • Bottom: Verify Bottom Layer.
      • Coated Component Placed: Verify only the layer with Coated Components placed.
  • Checking
    • Coated Component: Verification related to essential coating components.
      • Clearance to Panel edges: Clearance between Coated Component and Panel Area (Min/Max) (Omitting when no Panel Outline is present).
      • Clearance to PCB Outline: Clearance between Coated Component and PCB Outline.
      • Clearance to Slit and Cut-out: Clearance between Coated Component and Slit/Cut-out.
      • Clearance to non-coated Components: Clearance between Coated Component and Coating Restricted Parts.
        • Clearance between PTH (DIP) Pads on the Opposite Side of Component Placement among Coating Restricted Parts and Coated Components.
      • Clearance to Test Point(Pad): Clearance between Coated Component and Test Point Pad.
      • Clearance to non-coated Area: Clearance between Non-coated Areaand Coated Components.
        • Top
        • Bottom
      • Hole existence beneath Component: Verify the Presence or Absence of Specific Via or NPTH in the Coated Component Area (**Exclude QFP and QFN components with Thermal Pads at the center)
        • Item: Specify the item name.
        • Type: Select via type
        • Padstack/Hole Size: Set the padstack string filter and hole size.
        • Minimum Count: Set the minimum count via.
    • Coated Area: Verify Coated Area-Related (Deactivated if Coated Area is not set).
      • Coated component placed in the Coated Area: Verify the Placement of Coated Components Within the Coated Area (Deactivated if Artwork Layer is not set in the Coated Area).
      • Clearance to Panel edges: Clearance between Coated Area and Panel Area (Min/Max) (Omitting when no Panel Outline is present).
      • Clearance to Test Point (Pad): Clearance between Coated Area and Test Point Pad.
      • Clearance to Non-coated Area: Clearance between User-Defined Non-coated Area Drawn on the Artwork Layer and Coated Area.
        • Top
        • Bottom
      • Prohibited Via: Verify the Placement of Forbidden Vias in the Coated Area.
        • PSR(Solder Resistor) un covered Via: All Vias not covered by PSR (Vias with Solder Mask).
        • Padstack String: Set the Verification Target Vias using Padstack String Filter.
        • Exclude checking for Vias beneath Components: Excluding Restricted Vias Placed Below Specific Components from the Verification.
          • Measure

Dip Coating

  • Definition
    • Dip Line Layer: Define of the Artwork Layer with Drawn Dip Lines (Dip Line is straight line crossing the PCB).
    • Connector for Dip coating fixture: Define of Connector Component Attached to Dip Coating Fixture.
      • Measure
  • Checking
    • Clearance between Dip line and Connector (for fixture): Verify the Clearance Between Dip Line and Fixation Connector. If the inspected object crosses the Dip Line, it is considered as fail regardless of the Clearance.
    • Components below the Dip line: Verify the Components that Must be Placed Below Dip Line in the Direction of Dipping.
    • Component Group: Set the Components and Measure Base that Should be Located Below the Dip Line.
      • Measure
    • Clearance to Dip line: Verify the Clearance Between Components Set in the Component Group and the Dip Line.